Collaboration with Foxconn Interconnect Technology (FIT) Provides Solutions for Data Centers and High-Performance Computing
San Jose, Calif., August 17, 2021 – Point2 Technology, a leading provider of high-performance, low-power connectivity solutions for cloud and 5G infrastructure, and Foxconn Interconnect Technology (FIT), an innovative market leader of connectivity technologies within data center, mobile, computing and IoT environments, today announced expanded production of Point2’s Active Electrical Cable (AEC). The solution reflects the increased demand for the company’s first 400GBASE-SR4 AEC based on its C-TubeTM technology and a proprietary PAM4 SoC.
“When Point2 announced the PT-QD20132 last month, we expected it would be readily adopted,” said Sean Park, CEO of Point2 Technology. “Interest has actually been much greater, and for us to accommodate the demand from cloud and enterprise customers—Point2 was encouraged by our customers to team up with market leaders, such as Foxconn Interconnect Technology, to accelerate volume deployments. This demonstrates our ability to quickly and smoothly meet the very high volume demand for AECs with high quality, innovative and cost effective solutions.”
“We believe this is because AECs have advantages over passive direct attach copper (DAC) and active optical cable (AOC) in for short-reach applications. For example, they offer up to five times the reach in applications such as Base-SR4 400G, using about 80% less cable, with a 50% reduction in size, and 75% less power consumption than optical fiber cables,” Sean Park added.
Point2’s partnership with FIT demonstrates the ability to produce high performance interconnect solutions and offer a low cost, high-performance alternative to expensive AOCs and performance-limited DACs to proliferate 400G disaggregated chassis configurations at hyperscalers and service providers. The company will be able to get to production quickly because of Point2’s comprehensive reference design including the “paddle board” PCB, software and built-in self-test capabilities ideal for high quality volume manufacturing.
Unlike other AEC Ethernet solutions that do not include self-test capability, the PT-QD20132 has an integrated processor that provides access to Digital Diagnostic Monitoring (DMM) via the 2-wire QSFP management interface. This enables eye monitoring, PRBS pattern generation and checking, user-defined pattern generation, DC offset and phase calibration, eye and equalizer calibration, and loss of signal detection, without the need for external circuits. In addition, customization firmware can be downloaded to the PT-QD20132 to satisfy the needs of specific applications.
About the 400G Active Electrical Cable
The hot-pluggable PT-QD20132 accepts eight lanes of 53.125 Gb/s PAM4-modulated signals in each direction over a length of 7 m for an aggregated data rate of 425 Gb/s, and bit error rate performance is 10-8 or less. It easily replaced existing AOC assemblies because it has the same standard QSFP56-DD form factor, so it can replace bulky 400G QSFP56 DAC copper cables as well. The PT-QD20132 consumes just 4.5 W per cable end at 3.3 VDC and has a bend radius is 3 cm. The PAM4 SoC in the PT-QD20132 has embedded clock and data recovery (CDR) functionality and employs low-power, high-performance digital signal processing to compensate for the effects of intersymbol interference.
A unique feature of the PT-QD20132 is its self-test capability enabled by an integrated MCU that provides access to Digital Diagnostic Monitoring (DMM) via a two-wire QSFP management interface. These capabilities allow eye monitoring, PRBS pattern generation and checking, user-defined pattern generation, DC offset and phase calibration, eye and equalizer calibration, and loss of signal detection, without the need for external circuits. In addition, customization firmware can be downloaded to the PT-QD20132 to satisfy the needs of specific applications.
Foxconn Interconnect Technology (FIT) and Point2 will be demonstrating its low-power 400G Active Electrical Cable (AEC) SoC and reference design at Designcon at the San Jose McEnery Convention Center, August 16-18, 2021.
The PT-QD20132 is available in lengths of 3, 5, and 7 m terminated in 76-pin edge connectors. It is sampling now and expected to be in production by Q2 2022. Module manufacturers are encouraged to contact Point2 Technology for information about integrating the company’s PAM4 SoC into their products.
About Point 2 Technology
Point2 Technology, headquartered in San Jose, Calif., designs and manufactures low-power, high-speed, point-to-point interconnect and range enhancement solutions designed to meet the bandwidth requirements of cloud-based data centers at 5G infrastructure. For more information, please contact Point2 at [email protected] or www.point2tech.com.
About Foxconn Interconnect Technology
Foxconn Interconnect Technology (FIT) is a leading global solutions developer and manufacturer cultivating connectivity for a better world. With unsurpassed capabilities in development, research, manufacturing engineering and design, production, supply chain, and go-to-market planning for world class brands and private label products spanning B2C and B2B categories, FIT is at the forefront of worldwide technological trends delivering compelling user experiences at scale. With offices and manufacturing sites located in Asia, the Americas and Europe, FIT is a global leader in the manufacturing of high precision interconnect components. For more information, visit FIT’s website: fit-foxconn.com.